Page 4 of 5

Re: Suspension upgrades for bullbar?

Posted: Mon Dec 15, 2014 2:25 pm
by Tink
Hey app master, just one comment on using spacers with progessive rate coils. Not sure if this is what you have installed. But with progressive rate coils, fitting a spacer only loads the coil up a bit, and in turn you lose some of the progressiveness, or with larger spacers, all of the progressiveness. Better to fit the right coil than use spacers IMHO.

Re: Suspension upgrades for bullbar?

Posted: Mon Dec 15, 2014 2:35 pm
by Danno
Tink wrote:Hey app master, just one comment on using spacers with progessive rate coils. Not sure if this is what you have installed. But with progressive rate coils, fitting a spacer only loads the coil up a bit, and in turn you lose some of the progressiveness, or with larger spacers, all of the progressiveness. Better to fit the right coil than use spacers IMHO.
Used to level the car only, and by small increments usually.

Re: Suspension upgrades for bullbar?

Posted: Mon Dec 15, 2014 3:06 pm
by app_master
Danno wrote:
Tink wrote:Hey app master, just one comment on using spacers with progessive rate coils. Not sure if this is what you have installed. But with progressive rate coils, fitting a spacer only loads the coil up a bit, and in turn you lose some of the progressiveness, or with larger spacers, all of the progressiveness. Better to fit the right coil than use spacers IMHO.
Used to level the car only, and by small increments usually.
Combo uses a linear coil spring with optional spring seat spacer. Which I have used. For more height, such as those seeking 40+mm or more, you may have to look elsewhere, but this seems to work well for me atm, holding up and maintaining the ride height acheived. Links and details to it here.
Spring - http://www.outbackarmour.com.au/lp.php?pn=OASU1019001
Strut - http://www.outbackarmour.com.au/lp.php?pn=OASU0860007
Fitting guide - http://portal.outbackarmour.com.au/dl.p ... 33f38dadb5

Re: Suspension upgrades for bullbar?

Posted: Thu Dec 18, 2014 9:59 am
by ROSCO
Great info guys
:D

Re: Suspension upgrades for bullbar?

Posted: Thu Dec 18, 2014 3:44 pm
by mydmax
Does the use of spacers really "load up a coil"?

I would have thought all it does is reposition the coil further away from the fixed member/chassis mounting, thereby creating a lift, but no difference to suspension action apart from using up some of the droop value of lower arm.

Re: Suspension upgrades for bullbar?

Posted: Thu Dec 18, 2014 5:35 pm
by Tink
My thoughts are you will be reducing the overall length of the coil by using spacers and as such would be putting a small but constant amount of compression on the spring. Therefore you must be putting some load on the coil by using spacers. Any load would reduce the first stage of a progressive coil. Yes or no?

Tink

Re: Suspension upgrades for bullbar?

Posted: Sat Dec 27, 2014 1:09 pm
by Damian73
Tink wrote:My thoughts are you will be reducing the overall length of the coil by using spacers and as such would be putting a small but constant amount of compression on the spring. Therefore you must be putting some load on the coil by using spacers. Any load would reduce the first stage of a progressive coil. Yes or no?

Tink
No. Unless you have maxed out the downward travel (not advised), it will operate as per the post above, simply moving the whole coil down a bit.

Re: Suspension upgrades for bullbar?

Posted: Sat Dec 27, 2014 2:24 pm
by Tink
OK, I think there may be some confusion, probably on my behalf :D
Tink wrote:My thoughts are you will be reducing the overall length of the coil by using spacers and as such would be putting a small but constant amount of compression on the spring. Therefore you must be putting some load on the coil by using spacers. Any load would reduce the first stage of a progressive coil. Yes or no?

Tink
My above arguement was based upon using spacers within the strut, i.e. between the coil and the top or bottom plates. I think what others are referring to is using spacers outside of the strut assembly, i.e. between the strut and the chassis. If using spacers outside the strut assembly, then there would be no compression on the coil and it wouldn't effect its performance.

Re: Suspension upgrades for bullbar?

Posted: Sat Dec 27, 2014 4:03 pm
by mydmax
Spacers in or outside a strut is carrying the same weight of vehicle per corner as each other. What is the difference?
One the strut is spaced down with shock in normal position, other has the coil more pre stressed ie, harder riding but can't accept as much movement of stroke other wise the spring will become solid under full compression. That will make for interesting forces being applied to the strut tower and possible technical repairs.
The whole idea of a suspension is absorbtion and compliance, yet some folk want to reduce it. Strange phenomenon that.

Re: Suspension upgrades for bullbar?

Posted: Sat Dec 27, 2014 4:19 pm
by Damian73
Ah, I see what you are saying Tink... Yes, I was referring to the spacer between the top of the coil and the strut tower (like what I have in Booger Mobile)... I guess in one of those strut/coil combo situations, inserting a spacer in there would put the coil under load, as the strut would be maxed out when fully extended... Makes sense!!